W D icked evice TX+ TX- RX- RX+ FULL HALF DUPLEX TX RX RS-485 Breakout rs485.wickeddevice.com v1.0 GND GND TX_EN /RX_EN Isolated VCC2 VCC Linear Technology Devices http://www.linear-tech.com <author>Created by librarian@cadsoft.de</author> 28-Lead Plastic Small Outline Isolation Barrier (Wide .300 Inch) Reference LTC DWG # 05-08-1690 Source: www.linear.com >NAME >VALUE Diodes Based on the following sources: <ul> <li>Motorola : www.onsemi.com <li>Fairchild : www.fairchildsemi.com <li>Philips : www.semiconductors.com <li>Vishay : www.vishay.de </ul> <author>Created by librarian@cadsoft.de</author> DIODE >NAME >VALUE Transformers Based on the following previous libraries: <ul> <li>trafo-b.lbr: transformers from BLOCK <li>trafo-e.lbr: transformers from ERA <li>trafo-r.lbr: ring cores </ul> <author>Created by librarian@cadsoft.de</author> Transformer, Push-Pull 300kHz, 547uH, ER 9.5, SMT, gull wing, 8 pads Source: COOPERE ELECTRONIC TECHNOLOGIES .. ctx02-14659.pdf >NAME >VALUE Generated from nanodeRF_11.sch by exp-project-lbr.ulp >VALUE + >NAME <h3>SparkFun Electronics' preferred foot prints</h3> In this library you'll find resistors, capacitors, inductors, test points, jumper pads, etc. We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com. Licensing: CC v3.0 Share-Alike You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. >NAME >VALUE <h3>SparkFun Electronics' preferred foot prints</h3> In this library you'll find non-functional items- supply symbols, logos, notations, frame blocks, etc. We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com. Licensing: CC v3.0 Share-Alike You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. Wago Screw Clamps Grid 5.00 mm <author>Created by librarian@cadsoft.de</author> WAGO SCREW CLAMP >VALUE >NAME 1 2 3 4 5 6 EAGLE Design Rules for *2* Layer Designs (DS) This Sunstone Circuits 2 Layer .DRU has been set to cover our minimum requirements for our double sided products. For questions, comments, suggestions, please contact Sunstone Customer Support: Email: mailto:support@sunstone.com Phone: 800-228-8198. v1.1Mod10/16/07~Layers-core reversal.Distance C/D.Restring%.Supply G%. v1.2 Mod12/06/07~Distance C/D to 20mils.v1.3Mod12/12/07~Supply/Annulus Value to 12.5mils1/15/08 SSC-EAGLE-2Lyr_v1.0.0.3~For Release10/3/08 Description Edit. Attention: Upon running the design check and making modifications, please remember to save any changes before closing the application and sending in your board file to Sunstone Circuits for conversion.