/* ORion: OpenRelief Ion Chamber Radiation Detector
- http://openrelief.org
Copyright: 2012 Andrew Back
2011 James Coliz (Pachube/Cosm Ethercard example)
2011 Rufus Cable (Nanode MAC addr chip code)
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see . */
#include
#define JFET A0 // Nanode pin connected to JFET source
#define METER 3 // Nanode pin connected to moving coil meter (not used at present)
#define HOLD_LOW 300 // Time in ms to hold the JFET source low
#define READ_DELAY 500 // Time in ms between taking voltage readings
// Set the Cosm feed ID and API key
#define FEED "60745"
#define APIKEY "secretkey"
typedef byte bytes6_t[6];
int voltageDrift;
byte mymac[6];
// Static IP configuration to use if no DHCP found
static byte static_ip[] = { 0,0,0,0 };
static byte static_gw[] = { 0,0,0,0 };
static byte static_dns[] = { 0,0,0,0 };
char website[] PROGMEM = "api.cosm.com";
byte Ethernet::buffer[500];
uint32_t timer;
Stash stash;
void printf_begin(void);
void read_MAC(byte*);
void measure_drift(int);
void setup()
{
Serial.begin(9600);
printf_begin();
printf_P(PSTR("OpenRelief Ion Chamber Radiation Detector v0.1\n\r"));
read_MAC(mymac); // Fetch the MAC address
printf_P(PSTR("MAC: %02x:%02x:%02x:%02x:%02x:%02x\n\r"),
mymac[0],
mymac[1],
mymac[2],
mymac[3],
mymac[4],
mymac[5]
);
if (ether.begin(sizeof Ethernet::buffer, mymac) == 0)
printf_P(PSTR( "Failed to access Ethernet controller\n\r"));
if (!ether.dhcpSetup())
{
printf_P(PSTR("DHCP failed, using static configuration\n\r"));
ether.staticSetup(static_ip, static_gw);
ether.copyIp(ether.dnsip, static_dns);
}
ether.printIp("IP: ", ether.myip);
ether.printIp("GW: ", ether.gwip);
ether.printIp("DNS: ", ether.dnsip);
if (!ether.dnsLookup(website))
printf_P(PSTR("DNS failed\n\r"));
ether.printIp("SRV: ", ether.hisip);
}
void loop()
{
if(Stash::freeCount()<5){ // reset EtherCard stash if running low
Stash::initMap(56);
}
voltageDrift = measure_drift();
printf_P(PSTR("Level: "));
Serial.println(voltageDrift);
ether.packetLoop(ether.packetReceive());
if (millis() > timer) {
timer = millis() + 10000;
printf_P(PSTR("Posting to Cosm feed...\n\r"));
// generate two fake values as payload - by using a separate stash,
// we can determine the size of the generated message ahead of time
byte sd = stash.create();
stash.print("radiation,");
stash.println((word) voltageDrift);
stash.save();
// generate the header with payload - note that the stash size is used,
// and that a "stash descriptor" is passed in as argument using "$H"
Stash::prepare(PSTR("PUT http://$F/v2/feeds/$F.csv HTTP/1.0" "\r\n"
"Host: $F" "\r\n"
"X-ApiKey: $F" "\r\n"
"Content-Length: $D" "\r\n"
"\r\n"
"$H"),
website, PSTR(FEED), website, PSTR(APIKEY), stash.size(), sd);
// send the packet - this also releases all stash buffers once done
ether.tcpSend();
}
}
// Functions below here
int serial_putc( char c, FILE * )
{
Serial.write( c );
return c;
}
void printf_begin(void)
{
fdevopen( &serial_putc, 0 );
}
// Measure JFET gate voltage drift over a fixed period
int measure_drift() {
pinMode(JFET, OUTPUT); // Hold JFET gate low for a period
digitalWrite(JFET, LOW);
delay(HOLD_LOW);
pinMode(JFET, INPUT); // Prepare to read JFET gate voltage
int v1 = analogRead(JFET); // Take first reading
delay(READ_DELAY); // Wait
int v2 = analogRead(JFET); // Take a second reading
return (v2 - v1); // Calculate drift
}
// Nanode_MAC
// Rufus Cable, June 2011 (threebytesfull)
// Sample code to read the MAC address from the 11AA02E48 on the
// back of the Nanode V5 board.
// This code is hacky and basic - it doesn't check for bus errors
// and will probably fail horribly if it's interrupted. It's best
// run in setup() - fetch the MAC address once and keep it. After
// the address is fetched, it puts the chip back in standby mode
// in which it apparently only consumes 1uA.
// Feel free to reuse this code - suggestions for improvement are
// welcome! :)
// http://ww1.microchip.com/downloads/en/DeviceDoc/DS-22067H.pdf
// http://ww1.microchip.com/downloads/en/devicedoc/22122a.pdf
// Nanode has UNI/O SCIO on PD7
#define D7_ON _BV(7)
#define D7_OFF (~D7_ON)
#define SCIO_HIGH PORTD |= D7_ON
#define SCIO_LOW PORTD &= D7_OFF
#define SCIO_OUTPUT DDRD |= D7_ON
#define SCIO_INPUT DDRD &= D7_OFF
#define SCIO_READ ((PIND & D7_ON) != 0)
#define WAIT_QUARTER_BIT delayMicroseconds(9);
#define WAIT_HALF_BIT delayMicroseconds(20);
#define NOP PORTD &= 0xff
// Fixed Timings
// standby pulse time (600us+)
#define UNIO_TSTBY_US 600
// start header setup time (10us+)
#define UNIO_TSS_US 10
// start header low pulse (5us+)
#define UNIO_THDR_US 6
// SCIO Manipulation macros
#define BIT0 SCIO_HIGH;WAIT_HALF_BIT;SCIO_LOW;WAIT_HALF_BIT;
#define BIT1 SCIO_LOW;WAIT_HALF_BIT;SCIO_HIGH;WAIT_HALF_BIT;
// 11AA02E48 defines
#define DEVICE_ADDRESS 0xA0
#define READ_INSTRUCTION 0x03
// Where on the chip is the MAC address located?
#define CHIP_ADDRESS 0xFA
inline bool unio_readBit()
{
SCIO_INPUT;
WAIT_QUARTER_BIT;
bool value1 = SCIO_READ;
WAIT_HALF_BIT;
bool value2 = SCIO_READ;
WAIT_QUARTER_BIT;
return (value2 && !value1);
}
void unio_standby() {
SCIO_OUTPUT;
SCIO_HIGH;
delayMicroseconds(UNIO_TSTBY_US);
}
void unio_sendByte(byte data) {
SCIO_OUTPUT;
for (int i=0; i<8; i++) {
if (data & 0x80) {
BIT1;
} else {
BIT0;
}
data <<= 1;
}
// MAK
BIT1;
// SAK?
/*bool sak =*/ unio_readBit();
}
void unio_readBytes(byte *addr, int length) {
for (int i=0; i> 8);
unio_sendByte(CHIP_ADDRESS & 0xff);
// read 6 bytes
unio_readBytes(mac_address, 6);
// back to standby
unio_standby();
// interrupts ok now
sei();
}